tX-USBx10G

 It has already been 12 years since SOtM released the world’s first High End audio grade USB host card, tX-USB. During this long period of time, SOtM has released several products, including the USB hub type products as the tX-USBhub and tX-USBultra, and the tX-USBexp which is the upgraded in the PCI type of tX-USB to PCI express type, which are all recognized as still the best in the industry.

 And finally, these tX-USB series products, which have been a long run for about 12 years, were upgraded to the tX-USBx10G.

The tX-USBx10G, as you may already get a hint from the model name, it supports USB 3.1 Gen 2×1 specification, supporting USB SuperSpeed of up to 10Gbps.

 Over the past 12 years, the USB specification has continued to develop, supporting speeds of up to 20Gbps. However, to support this speed, a USB type C cable must be used which means that it can’t be directly used for most USB audio devices that require only using the Type A to Type B cable.

 As a result, the tX-USBx10G applies the USB 3.1 Gen 2×1 specification that can support the fastest speed among the specifications that can be directly connected to the Type A to Type B cable used for High End USB audio devices without the need for a separate conversion gender.

 The most noticeable improvement in sound aspect of the tX-USBx10G is that it expresses singer’s voice and textures of instruments without distortion very clearly, as if they were present at the scene. In addition, even emotions of performers who exchange music each other and where the microphone was installed and recorded can be easily revealed well.

 However, it can be said that the biggest improvement of using tX-USBx10G is not only the improvement of detailed expressions, but also the ability to feel the taste of beautiful music alive.

 This improvement in the sound aspect can be said to be such a significant advancement that can be divided into the era of USB audio as well as PC audio before and after the release of the tX-USBx10G. If previous tX-USB series products can be described as perfect for improving sound quality for USB audio, the tX-USBx10G, which is a remarkable step forward in technology and sound quality, is at the stage of sound perfection.

 Simply saying, the tX-USBx10G is so special enough that it’s meaningless to look for an alternative to it, so it is time to forget about the old dated digital audio.

 The tX-USBx10G will give you a very special experience how you can feel the ‘Soul of The Music’ in your audio system.

Key features

  • USB 3.2 Gen 2 x1 (Previously USB 3.1 Gen 2) host card
  • Support SS(Up to 10Gbps), HS(480 Mbps), FS(12 Mbps), LS(1.5 Mbps)
  • USB type A connector for external USB audio device
  • USB type E connector for internal USB audio device
  • Internal SATA power connector, External power DC jack
  • Status LEDs
  • USB power on/off switch and jumper
  • Max 2.0A USB type A port power, Max 1.5A USB type E port power
  • Internal clock and external clock

Reviews

Specification

PCI express USB interface chip set
   USB 3.2 Gen 2 x1 (Previously USB 3.1 Gen 2) host controller
   Support SS(Up to 10Gbps), HS(480 Mbps), FS(12 Mbps), LS(1.5 Mbps)
   PCIe Gen 3 x2 interface
User interface LED
   Located underneath of USB type A connector
     Green LED : Internal power on indicator
     Red LED : USB type A port power on indicator
     Amber LED : External power input indicator
     Blue LED : Operating indicator
Internal SATA power input
   Input voltage : +12.0V(+0.5V, -0.5V)
   Input current : 3A
   15pin SATA power connector 
External power input
   Input voltage : +7V ~ +9Vdc
   Input current : 5A max
   5.5mm OD, 2.1mm ID DC adaptor jack
USB Type A port output power 
   Output voltage : +5.0V(+0.5V, -0.25V)
   Over current protection : 3.0A(Tolerance 20%)
   Recommend output current : 2.0A >
   Power on/off switch : S401
USB Type E port output power 
   Output voltage : +5.0V(+0.5V, -0.25V)
   Over current protection : 2.0A(Tolerance 20%)
   Recommend output current : 1.5A >
   Power on/off jumper : J402(Jumper on : off)
External clock jumper
   Internal clock setting
     Install two jumpers on J107
     Uninstall J106
   External clock setting

     Uninstall two jumpers on J107
     Install J106
Operating environment
   Operating temperature : 0°C ~ 30°C
   Storage temperature : -10°C ~ 50°C
   Operating & storage humidity : 10% ~ 90%
OS support
   Windows 10 or higher version
   Linux kernel 5.xx or higher version

FAQ